Weil Mclain WGO™ Series 4 122K BTU, 86.2% AFUE Hot Water Oil Boiler with beckett burner Model W386701014 Item 1134

Sale price $8,290 includes Removal of Old unit and dispose, supply and Install new Unit For Single zone 1 section only each additional sections are $450 additional

WGO
CAST IRON OIL BOILER

STANDARD EQUIPMENT:
BOILER
■ Factory tested and assembled cast
iron section assembly
(jacket and collector hood are not assembled
on the 7 size section block)
■ Insulated steel jacket
■ Aluminized steel flue collector hood
with flue cap on top outlet
(convertible to rear outlet)
■ Swing-away burner mounting door
■ Refractory blanket and target wall
in combustion area
■ Circulator (when ordered)
− Sizes 2–4: Taco 007e
− Sizes 5–6: Taco 007
■ High limit control with circulator
relay, LWCO function, and integrated
service switch
■ Two vent pipe brackets
■ Pressure / temperature gauge
■ 30 PSIG ASME relief valve
(boiler sections tested for 50 PSIG
working pressure)
■ Drain valve
■ Barometric damper
■ Built-in air separator
OPTIONAL EQUIPMENT:
■ High-efficiency flame-retention oil
burner (Beckett AFG, Carlin EZ or Riello).
Specify 2-stage fuel unit (optional,
Beckett) if required
■ Vent damper kit
■ Outdoor reset kit - temperature sensor
(wired version part #383-500-126, wireless
version part #386-701-047)
■ Weil-McLain five- and ten-year
homeowner protection plan
■ Weil-McLain indirect-fired
water heaters

LIMITED TRANSFERABLE
WARRANTY:
■ Residential: 2 0 Years Heat Exchanger;
2 Years Parts
■ Commercial: 1 0 Years Heat Exchanger;
1 Year Parts
4 Boiler model suffixes:
R = Reduced input version—a burner nozzle change may
be required, refer to the burner instructions or boiler's
rating label for correct selection. No separate/additional
damper kit required.
D = High input version—installation of the separate
High Input Vent Damper kit (part # 381800515) is
required, also a burner nozzle change may be required,
refer to the burner instructions or boiler's rating label for
correct selection.
RD = ENERGY STAR 87% AFUE compliant only when
installed with the separate ES Vent Damper kit (part
numbers 381800501 through 381800506) and at the
reduced burner rate.
5 No. 2 fuel oil-Commercial Standard Specification CS75-
56. Heating value of oil-140,000 BTU / Gal.
6 Based on standard test procedures prescribed by the
United States Department of Energy.
7 MBH refers to thousands of BTU per hour.
8 Net AHRI ratings are based on net installed radiation
adequate for the requirements of the building, including
a piping and pickup allowance of 1.15-sufficient for normal
conditions.

Weil-McLain WGO Series is a line of cast iron oil-fired boilers designed for residential and light commercial heating applications. It is known for its durability, high-quality construction, and reliable performance. The WGO Series offers a two-pass design and is available in multiple sizes to accommodate various heating requirements.

Key features of the Weil-McLain WGO Series cast iron oil boiler include:

Efficiency: The WGO Series boilers are designed for high efficiency, helping to reduce fuel consumption and lower heating costs.


Cast Iron Construction: The boilers are constructed with durable cast iron, which provides excellent heat retention and ensures long-term reliability.

Multiple Firing Rates: The WGO Series offers multiple firing rates, allowing the boiler to match heating demands accurately.

Easy Installation: The compact design and multiple installation options make it easier for HVAC professionals to install the boiler in different heating systems.

Venting Options: The WGO Series boilers can be vented through a chimney or using direct venting, providing flexibility in installation.

Quiet Operation: The cast iron construction and advanced engineering contribute to the boiler's quiet operation, minimizing noise disruptions.


Energy Star Rated Options: Some models in the WGO Series may be ENERGY STAR certified, meeting strict energy efficiency guidelines set by the Environmental Protection Agency (EPA).

It's important to note that specific features and availability may vary depending on the model and size of the Weil-McLain WGO Series boiler. As product offerings and specifications can change over time, I recommend calling Instally Long Island today we serve in Suffolk and Nassau counties as well as in Queens . If you are considering installing a boiler, consulting with us is crucial to determine the right size and model that best suits your heating needs and property requirements.
Weil-McLain WGO Series Standard Equipment:
BOILER
■ Factory tested and assembled cast
iron section assembly
(jacket and collector hood are not assembled
on the 7 size section block)
■ Insulated steel jacket
■ Aluminized steel flue collector hood
with flue cap on top outlet
(convertible to rear outlet)
■ Swing-away burner mounting door
■ Refractory blanket and target wall
in combustion area
■ Circulator (when ordered)
− Sizes 2–4: Taco 007e
− Sizes 5–6: Taco 007
■ High limit control with circulator
relay, LWCO function, and integrated
service switch
■ Two vent pipe brackets
■ Pressure / temperature gauge
■ 30 PSIG ASME relief valve
(boiler sections tested for 50 PSIG
working pressure)
■ Drain valve
■ Barometric damper
■ Built-in air separator
OPTIONAL EQUIPMENT:
■ High-efficiency flame-retention oil
burner (Beckett AFG, Carlin EZ or Riello).
Specify 2-stage fuel unit (optional,
Beckett) if required
■ Vent damper kit
■ Outdoor reset kit - temperature sensor
(wired version part #383-500-126, wireless
version part #386-701-047)
■ Weil-McLain five- and ten-year
homeowner protection plan
■ Weil-McLain indirect-fired
water heaters
LIMITED TRANSFERABLE WARRANTY:
■ Residential: 20 Years Heat Exchanger;
2 Years Parts
■ Commercial: 10 Years Heat Exchanger;
1 Year Parts

What Weil McLain WGO Series boiler include with the purchase?
II. Product

A. Acceptable boiler manufacturer(s) include(s):
1. Weil-McLain only, as specified in Part 1, Paragraph C.
2. Other manufacturer or other Weil-McLain boiler(s) must comply with specifying engineer’s requirements, including:
• Full intent of these specifications, and
• Provide complete submittal including literature, wiring diagrams, fuel piping diagrams, and a list of similar installations.
• Submittals to be presented to specifying engineer at least seven working days for approval before bid opening. Substitutions are not permitted after contract is awarded.
B. Boiler construction
1. Boiler sections
• Factory assembled in one block with tie rods and sealed with high temperature sealant to assure a permanent gas-tight seal.
• Rear section shall encompass a recessed target wall to protect the combustion chamber from flue brush damage.
• Sealed watertight by elastomer sealing rings, not cast iron nipples. Each port opening shall be machined to completely capture sealing ring between sections in order to assure uniform compression of the sealing rings and to protect the sealing rings from contaminants.
• Provided with sufficient tappings to install required controls.
• Boiler(s)-
• Provided with cast-in air elimination to separate air from circulating water.
• Provided with a swing-away burner mounting door to allow greater ease of service.
• Provided with the means to vent out the top or out the rear of the boiler.
• Shipped with insulated heavy gauge steel jacket(s) with durable powdered paint enamel finish. Jacket designed to be installed after connecting supply and return piping.
C. Boiler foundation(s)
1. Installer shall construct required level concrete foundation(s) and support(s) where boiler room floor is uneven or will not support the weight of the boiler(s).
D. Boiler trim
1. All electrical components to be of high quality and third (3rd) party recognized.
2. Electrical wiring to utilize a labeled and color-coded wiring harness to help assure correct wiring.
3. Water boiler(s) standard controls furnished:
• Temperature limit control with circulator relay, integrated low water cut-off and power switch. (240 degrees F maximum allowable water temperature)
• Combination pressure-temperature gauge. Dial clearly marked and easy to read.
• A.S.M.E. certified pressure relief valve, set to relieve at 30 PSIG. Side outlet discharge type; installer to pipe outlet to floor drain or near floor.
4. Steam boiler(s) standard controls furnished:
• High pressure limit control. (15 PSI maximum allowable steam pressure)
• Steam pressure gauge. Dial clearly marked and easy to read.
• A.S.M.E. certified pressure relief valve, set to relieve at 15 PSIG. Side outlet discharge type; installer to pipe outlet to floor drain or near floor.
• Low water cut-off (LWCO), shall be ( ) electrode or ( ) float-mechanism (check one) type capable of shutting down the boiler in event of a low water situation.
E. Additional Components
1. Packaged WTGO Boiler(s) only: The boiler(s) shall be installed with a tankless heater with ½” inlet and outlet openings. The tankless heater opening shall be machined to completely capture sealing ring between the heater and the section.
2. Semi-packaged and Knock-down WTGO Boiler(s) and all SGO Boiler(s) only: The boiler(s) shall be provided with an opening for an optional tankless heater. A cover plate shall be installed over the opening.
F. Optional Components
1. WGO or WTGO Boiler(s) only: The boiler(s) shall be able to be provided with an optional relief valve set to relieve at 50 PSIG.
2. The boiler(s) shall be able to be installed with an optional tankless heater (Not available for Packaged WGO Boiler(s); standard on Packaged WTGO Boiler(s)).
• Tankless heater must be specified when order is placed.
• Tankless heater shall have ½” inlet and outlet openings for Semi-packaged or Knocked-down WTGO Boiler(s) and ¾” inlet and outlet openings for a SGO Boiler(s).
• If installed with a tankless heater, water boilers shall be furnished with a combination hi-low temperature limit control in lieu of standard hi limit control; steam boilers shall be furnished with an additional temperature limit control.
3. Packaged or Knock-down SGO Boiler(s) only: The boiler(s) shall be able to be provided with an optional low water cut-off (LWCO).
• LWCO must be specified when order is placed.
• LWCO shall be ( ) electrode or ( ) float-mechanism (check one) type capable of shutting down the boiler in event of a low water situation.
G. Boiler Manuals
1. The boiler(s) shall be provided with complete instruction manuals, including:
• Boiler Installation Manual
• Maintenance and Service Guide


Weil-McLain WGO Series Routine maintenance schedule
Beginning each heating season : Call Instally Long Island to perform annual service
Daily during heating season : Check that boiler area is free from combustible materials, gasoline
and other flammable vapors and liquids.
Weekly during heating season :
- Check for and remove any obstructions to flow of combustion or
ventilation air to boiler.
- Check that breeching is attached between boiler and chimney. If
breeching is loose or damaged, immediately turn off switch on
boiler and call service technician to repair.
- Check for oil leaks in oil piping and around burner. If found, immediately
call qualified service technician to correct situation.
- Check for water leaks in boiler and piping; also check for leaks
around tankless heater plate, if installed. If found, immediately call
service technician to repair.
End of heating season :
If tankless heater is installed, boiler will continue to operate. Check
for the following:
• All daily and weekly instructions listed on this page must be followed.
• Burner motor may have to be oiled. Some motors are permanently
lubricated and do not need additional oil. Check for oiling instructions
on burner or motor.

Boiler shutdown:
Do not drain boiler unless exposure to freezing temperatures will
occur.
- Always keep manual fuel supply shut off if burner is shut down for
an extended period of time.
• Turn off switch at boiler and any external switch to boiler.
• Close fuel valves.
• Turn off water feed valve.
• Cover burner to protect from dust and dampness

What Can I do if My Weil-McLain WGO Series does not work ?
1 - If burner does not fire, check for:
• Service switch on control or additional switches turned off.
• Fuses or breaker switch tripped.
• Thermostat set below room temperature.
• Fuel valves turned off.
• Not enough oil in tank to supply burner

2. Correct problems found in step #1. If burner does not fire,
press reset button on burner primary control only once.
Repeated presses will deposit oil in combustion chamber.
Burner must never be fired when oil is in combustion
chamber. Immediately call Instally Long Island service
technician.


What are the differences between Weil-Mclain WTGO And WGO Series?
Weil-McLain WTGO Series and WGO Series are both lines of oil-fired water boilers designed for residential and light commercial heating applications. While they share some similarities, they have key differences in their design and features. Here are the main differences between the two series:

1. Design and Construction:

WTGO Series: The WTGO Series features a three-pass design, allowing for increased heat transfer efficiency. These boilers have a cast iron construction, which provides excellent heat retention and durability.
WGO Series: The WGO Series, on the other hand, incorporates a two-pass design, making it slightly simpler in construction compared to the WTGO. Like the WTGO, it also has a cast iron construction for heat retention and longevity.
2. Efficiency:

WTGO Series: The WTGO Series typically offers slightly higher efficiency compared to the WGO Series. Its AFUE ratings are generally in the range of 85% to 87%.
WGO Series: The WGO Series also provides good efficiency, with AFUE ratings similar to the WTGO Series, typically around 85% to 87%.
3. Size Range:

WTGO Series: The WTGO Series comes in a range of sizes, offering more options for heating various sizes of homes or buildings.
WGO Series: The WGO Series also comes in multiple sizes, but the size range may be slightly different from the WTGO.
4. Application:
WTGO Series: The WTGO Series is suitable for residential and light commercial applications, offering reliable performance and efficiency for both.
WGO Series: The WGO Series is also designed for residential and light commercial use, making it a versatile choice for heating needs.
5. Venting Options:
WTGO Series: The WTGO Series provides both chimney venting and direct venting options, offering more installation flexibility.
WGO Series: The WGO Series also offers flexibility in venting, with options for both chimney venting and direct venting.

6. Specific Features:

While both series share many features typical of Weil-McLain boilers, there may be specific design or control variations between individual models within each series.
When choosing between the WTGO Series and WGO Series, consider factors such as your heating needs, available space, and budget. Additionally, consulting with us at Instally New York HVAC technician can help you select the right boiler for your specific requirements and ensure a successful installation. For the most up-to-date information and to compare the specific models available in each series


We are proud to serve in following areas
Town of Hempstead NY 11549, 11550, 11551
Town of Oyster Bay NY 11542, 11545, 11547, 11548, 11560
Town of North Hempstead NY 11001, 11005, 11020, 11021, 11022
Town of Long Beach NY 11561
Town of Glen Cove NY 11542, 11560, 11579
Town of Islip NY 11506, 11722, 11751
Town of Babylon NY 11701, 11702, 11703, 11704, 11707
Town of Huntington NY 11721, 11724, 11740, 11743
Town of Smithtown NY 11725, 11754, 11780, 11787
Town of Brookhaven NY 11719, 11733, 11772 11776,11777, 11790, 11794
Town of Riverhead NY 11901, 11931
Town of Southampton NY 11713, 11901, 11932, 11933, 11941
Town of East Hampton NY 11930, 11937, 11944, 11954, 11963, 11975
Town of Southold NY 11935, 11939, 11944,11948